|
|
|
ART ProMIX - 3 Channel Mic Mixer |
| |
| |
| The ART ProMIX is a 3 channel microphone mixer that can mix 3 mics down to a transformer-balanced mono XLR output. Also comes with a Aux/Headphone output. |
| |
| Product Name: |
ART ProMIX - 3 Channel Mic Mixer |
| Product Code: |
PROMIX |
| Brand: |
Art |
| |
|
 |
| |
| RRP |
AUD $199.99 |
| You Save |
AUD $20.00 |
| Our Price |
AUD $179.99 |
|
| |
|
|
| |
ART ProMIX - 3 Channel
Mic Mixer
|
| |
Problem: You need to add 3 mics to a mixer, which only has one available channel.
Solution: Insert a ProMIX between the mics and the mixer. Each mic channel on the ProMIX has both phantom power and low-frequency cut selectable via DIP switches plus a level control. The balanced XLR line output can be connected to a mic input on the mixer and headphones or a powered monitor can be connected to the Phone/Aux output. And if AC power is not available, the ProMIX runs on batteries as well.
Features
- 3 low-impedance XLR mic channels
- 3 level controls
- 3 phantom power on/off DIP switches
- 3 low-frequency cut on/off DIP switches
- A low-impedance balanced XLR line output
- Mono 1/4 Phones/Aux. output
- Clip LED (fires 3dB below the onset of clipping)
- On/off Power switch, with LED
- Output Phantom Power: 12V DC
- Optional 2 x 9V Battery Power yields 18V Phantom Power
- Low Cut: -3dB @ 100Hz
- Input and Output Impedance: 600 ohms
Usage:
a.) If you are using the 12V AC adapter, connect the cable end to the ProMIX's
12V DC input and plug the other end into a 120V AC outlet. Otherwise, make
sure there are two 9V batteries connected inside the battery compartment.
b.) Connect low-impedance mics to the 3 XLR inputs with mic
cables.
c.) If any mics require phantom power, set the appropriate
Phantom DIP switches to the on position (down).
d.) To avoid picking up unwanted low-frequency noise (rumble,
thumps, etc.), it is advisable to roll off the low frequency
response of mics other than those specifically for bass drum,
bass guitar amp, upright bass or keyboard amps. For all other
mics, set the Low Cut switches to the on position (up).
e.) Connect the balanced XLR (male) Output to the mic input on
the mixer with a low-impedance mic cable.
f.) Connect headphones to the Phone/Aux jack. Alternatively this
jack can be connected to the unbalanced input of an amplifier,
another mixer, etc.
g.) Flip the Power switch to the ON position. The PWR (power) LED
will illuminate.
h.) Adjust the Level controls for the desired mix and check the
Clip LED to make sure one or more of them are not turned up
too far. A small amount of Clip LED activity on occasional peaks
is acceptable as it fires 3dB below the onset of actual clipping
distortion.
i.) Adjust the input gain of the other mixer for best signal strength
without distortion.
|
| |
ART ProMIX - 3 Channel
Mic Mixer
|
| |
| |
|
|
|
Specifications: |
| |
|
|
|
|
|
|
|
Maximum Gain +60dB
Input Impedance 600 ohms
Maximum Input Level -14dB
Maximum Output Level +14dB
Output Impedance 600 ohms
Total Harmonic Distortion 0.02%
Low Cut -3dB @ 100Hz
Clip Headroom 3dB
Output Phantom Power 12V DC
Power 12V DC (adapter) / 2x 9V (batteries)
Dimensions (143mm x 92mm x 45mm)
Weight (680g)
* Specifications subject to change without notice
|
| |
|
|
|
|
|
| |
|
|
|
|
